Fridge compressor hot but not running

Refrigerator compressor trouble? Often, the issue lies with the compressor. Troubleshooting Your Compressor — Refrigerator Running? How long has it been since you pulled out the fridge for a deep cleaning?

A dirty refrigerator compressor or condenser coils are common causes of poor fridge performance. Make sure to pull the fridge out once in awhile and give the coils a thorough cleaning with a damp cloth and dish soap. Your fridge draws a respectable amount of current, and no maintenance should be performed on your unit without first ensuring power has been terminated. Before restoring the power, make sure the back of the unit has had adequate time to fully dry. A steady hum usually means the compressor is working as intended.

Modern fridges are, however, much quieter, and may require you to access the back of the unit to ensure the compressor is running. In either case, if your compressor makes a clunking, creaking, mechanical noise, this is a bad sign. Your fridge also contains a condenser fan typically situated next to the compressor unit. This fan should spin freely on normal operation, but can also become blocked by debris, spills, or an errant wire or piece of hardware.

Inspect the fan to ensure it is clean and spins free of any blockage. Try plugging the fridge back in to make sure the fan is operating correctly; if not, you may need to replace the fan assembly. A good way to check for proper fan and compressor performance is to leave the doors open on the fridge for a few minutes while plugged in.

See if the compressor fails to engage or the fan fails to spin as the cool air empties from the unit.

fridge compressor hot but not running

If the compressor is clicking on and off, or worse, not running at all, check the start relay. This is a small box on the side of the compressor with several wires feeding in and out. Often, the relay can perform poorly if it is very dirty, or if one or more wires have been loosened from repeated wear.

Make sure the relay is clean, and that all wiring is properly fed and secured. If this does not address the problem and the compressor continues to operate incorrectly or not at allyou may unfortunately have a blown compressor that will require replacement. Inside your freezer, you will see several vents on the back of the compartment. These must not be blocked in order for the fridge to properly circulate cold air. If you can hear the compressor running but the refrigerator is not kezi road closures properly, move any food products blocking the vents, and scrape off any ice dams or spills that may be impacting the vents.If you have this issue with your Maytag, Samsung, LG, Kitchenaid or Frigidaire fridge probably this will apply to any fridge manufacturer been not cooling, you need to check couple things to fully understand the problem.

You need to check the temperature in your fridge compartment. There is a big probability that the compressor is lost efficiency in other words is dead or there is a restriction in freon sealed system usually on the dryer filter side.

In this case, you need to call Appliance Repair Technician to fix this issue. You will not be able to fix it by yourself in most cases. Now, this issue when not cooling enough is a little bit advanced and requires the right knowledge and tools to track it down and fix it.

Before you get the big repair tools and begin tearing your beloved fridge apart, start by double-checking the controls. This happens mostly if you have kids around who may unknowingly or purposefully dial in the incorrect cooling settings. If the temperature settings are wrong, just set them back to reasonable levels. Usually, the higher the temperature on the dial, the colder your fridge will get. You can always dial up the control temperature one number higher if the beverages are not getting as cold as you like.

Just remove the cover from the freezer compartment to access the coils. If you notice the coils are completely covered in frost, you have to thaw it for 24 to 48 hours. Always unplug the fridge, then transfer your items to another fridge to keep them preserved while you work on the faulty fridge. Remember to keep a few towels nearby to soak up water that leaks onto the floor as you thaw away the frost from the evaporator coils.

Check after 24 hours if the ice has melted away; But remember, thawing it for longer than 24 hours ensures all the frost from the frozen sections is completely melted. After melting all frost away, plug the fridge and test it, if it works, then the likely cause of the frozen evaporator coils is a faulty defrost timer, a faulty defrost thermostat or a bad defrost heater.

These parts may be replaced easily once you call in a pro to troubleshoot exactly which part is defective. Or if you want to speed up the defrosting process, you will need a steamer and you can defrost evaporator coils in 15 minutes. If your fridge is not cooling and this is accompanied by increased vibration and squealing noise whenever you open your fridge, then the likely cause of both problems is a faulty evaporator fan.

Fridge Repair: Fridge Doesn't Run, but Light Works

A stuck or broken evaporator fan usually makes chirping or squealing sounds. The evaporator fan is located inside the freezer compartment, near the coils, and covered by a fan cover. To verify this, open the fridge door and feel using your hand, at the back of the fridge, if the fan is blowing. If the temperature at the back of the compartment is the same level as that of the room, then the fan is not working.

Replacing the evaporator fan should fix the issue. You can get fan HERE. The compressor and condenser fan are located behind a rear access panel at the back of the fridge and usually come on if the thermostat demands more cooling. The condenser fan cools condenser coils by drawing air over them.

Refrigerator Compressor Will Not Turn On – Lights And Fans Work

Condenser fan providing proper heat exchange for the condenser coils.There are many different causes of a refrigerator not being able to function as it should, and a variety of problems that can lead to hundreds of dollars of spoiled, ruined food. A refrigerator normally cycles on and off in order to maintain an appropriate temperature, so many people mistakenly think that a quiet appliance has just shut off in its cycle when in fact, its compressor has stopped working.

Although a broken compressor is just one common problem with refrigerators, it can also be one of the most often overlooked, too. Pull your appliance away from the wall, and stand to listen for a few minutes and see if you hear the sound of a motor running, or a soft humming.

If you do hear a humming noise, but the food in your fridge is warm, your compressor may be functioning improperly or it may be a different issue causing the problem altogether. When a compressor is bad, the repairs can cost more than what a new appliance would. Posted By: Erin White Categories: beer caves. Email This Post. Print This Post. Quality Since The hottest location in a refrigeration system is at the discharge port of the valve plate inside the compressor head.

It is difficult for a technician to measure the exact temperature at this location. However, measuring the temperature of the discharge line approximately 6 inches from the compressor outlet will give a good indication of the temperature at the discharge port.

There will be approximately a 50 degree to 75 degree F drop in temperature between the discharge port and 6 inches out on the discharge line.

If a temperature of degrees is measured on the discharge line, it would indicate an approximate temperature at the compressor discharge port of between degrees and degrees. For a reciprocating compressor to operate properly, the temperature of the discharge port should never rise above degrees.

This means the discharge line temperature should never exceed degrees degrees minus 75 degrees. At temperatures between degrees and degrees inside the compressor, the refrigeration oil will start to lose its ability to lubricate.

At temperatures above degrees, the oil will start to break down, causing accelerated wear and allowing contaminants to enter the system. Once this occurs, compressor failure will soon follow. Possible Causes There are several reasons for a compressor to run too hot, including high compression ratio, high return gas temperatures, and lack of external cooling.

High compression ratios are the result of either lower than normal suction pressures or higher than normal discharge pressures. Changes in suction pressure will affect the compression ratio more rapidly than changes in the discharge pressure. For this reason, it is important to keep the suction pressure at its highest possible value. Causes of low suction pressure can include incorrect sizing of components, misadjusted or defective metering devices TXVsloss of refrigerant charge, plugged driers or strainers, and excessive suction line pressure drop.

Although not as sensitive to change as the suction pressure, the discharge pressure can still greatly affect the compression ratio. Keeping the discharge pressure within normal operating conditions is still important. Causes of high discharge pressure can include dirty condensing coils, undersized discharge line, a blockage or recirculation of condenser air, erratic condenser fan operation, refrigerant overcharge, noncondensibles in the system, and an undersized condenser.

Many larger refrigeration systems with electronic controllers will automatically monitor the temperature of the discharge line and will send out an alarm to alert the owner or service contractor of a potential problem.

Regardless of how the discharge line temperature is monitored, it should always be checked as part of any service to a refrigeration system. A technician should also check the discharge line temperature within 6 inches from the outlet of the compressor.

Any temperature above degrees should be investigated and the cause found and repaired. Marchese is owner of Coldtronics of Pittsburgh.If your fridge is not working even though the light is on, you might save yourself some money on costly repairs by doing some simple diagnostic checks to some of the possible causes. Some of it can be performed at home with a few basic tools. It is always a good idea to disconnect your refrigerator from the electrical supply before you undertake any repair project.

There is a temperature setting knob located inside the fridge. If the temperature is set too high, the compressor will not kick in and the fridge will not cool, so adjust the knob so that it is set to a lower temperature and see if the compressor starts. If not, there could be a problem with the temperature controller itself. If you are good at working on electrical projects, you can save some money and replace the temperature controller unit yourself.

Otherwise, you should ask a repairman to do it for you.

Your freezer and/or fridge are not as cold as usual, or not cold at all

Your fridge needs adequate room all around it for airflow. Ideally, there should be at least three inches of space between the fridge and the walls of your house, and at least one inch of space between the ceiling and the top of the fridge. If this is the problem, consider moving the fridge to a more suitable location. The black coils at the back of the fridge are known as condenser coils.

These coils are what allow the fridge to cool by dissipating heat. If they are not cleaned regularly, they can lose their efficiency and over a period of time, can stop cooling entirely.

fridge compressor hot but not running

Check to see that the condenser coils are clean, and if not, use a vacuum or a brush and some soap and water to thoroughly clean them. If the fridge is still not cooling, disconnect it from the mains for two hours.

Afterward, plug it back in and switch it on. If the compressor starts up, then there may be a problem caused by the compressor overheating. You should ask a professional to look into this problem. Older fridges come with a button for manual defrosting.A "Green Plug" is an electrical box that plugs into your power outlet.

The refrigerator is plugged into it, and it can save electric usage by modifying the power coming from your electrical outlet. In the "old days," refrigerators were overpowered. The electricity could be modified and some energy could be saved.

fridge compressor hot but not running

Since aboutbecause of government "Energy Efficiency" requirements, refrigerators are much more efficient, and they don't use NEAR the energy of older refrigerators. If you are using a "Green" plug, disconnect it now, or you may not be able to diagnose your refrigerator problems.

Door seals are held to the door by screws, which are accessed by lifting the seal away from the door. A magnet "sticks" the seal to the door frame and mullions. Look for gaps between the seal and the door frame. If you think you see one, make sure there is nothing jammed in the compartment that is preventing the door from fully closing. It seems obvious, but Slip a dollar bill between the seal and the door frame.

If you can slide the bill sideways, or up and down then the gap is too wide. It MAY be caused by a damaged seal, or the door may be warped a little. You will need to adjust the gap. I personally think that door seals are one of the most misunderstood pieces of the refrigerator. Ask a do-it-yourselfer about why his fridge is warm, and the first thing he'll say after "I don't do Freon" is "but let's check the door seals.

Unless the seal is shredded or you can physically see a gap between the seal and the door frame with the door closed, there is no reason to suspect a door seal problem. Door seals rarely have problems over the life of the fridge. The only ones I've seen go bad are in households that have dogs or cats that like to chew or sharpen their claws on them, or kids that climb or hang on the refrigerator door. A really bad door seal problem is most likely to show up as a defrost problem, due to humid air getting into the fridge.

To replace the seal, you must have a nut driver of the proper size. A power nutdriver is better. A magnetic tip may prevent you from going crazy trying to hold the driver, the screw and the seal at the same time.

There are lot of screws holding the seal on. One side at a time is better. The idea is to prevent the plastic inner door liner or shelving from drifting around — if you have to re-align it, it can be a long, frustrating, trial-and-error process.

The new seal will fit in the same way as the old one came out.

Refrigerator Isn’t Cooling — Refrigerator Troubleshooting

You can use a blow-dryer to soften the seal to shape it more easily.Question: The compressor on my refrigerator will not turn on no matter what I try. Everything else is working but the compressor. The compressor fan and evaporator fan turn normally when I plug the fridge in.

The lights inside the fridge work too. After I plug in the refrigerator there is a click I hear from the motherboard. The motherboard on my refrigerator is located at the back of my fridge behind a small metal plate behind the freezer section. There is no click, hum, or movement from the compressor at all. Is the compressor bad or is it the main control board? Can I just replace the motherboard? How do I know if the compressor is bad?

Answer: If everything else on the fridge is working…. A small relay on the motherboard main control board may not be sending the compressor voltage.

The condenser fan that is next to the compressor comes on at the same exact time as the compressor. If the condenser fan is running, the compressor should be on also. Use extreme caution here… Check the wire harness for voltage to the compressor while the fan is running. If your meter does not read V AC, then the compressor is not getting power from the board.

Remove and replace the main control board. Refrigerator Control Board. A bad or burned relay on a refrigerator control board for the compressor is a common failure.

fridge compressor hot but not running

The board is easy to replace. Unplug fridge 2. Unscrew back panel where board is located 3. Remove old board with wires attached 4. Pull off wires and connect to new board one at a time 5. Secure the new board to the fridge with the screws from the old board 6.

Secure back panel 7. Plug fridge in and hope for the best. Refrigerator Compressor. If you are getting V AC to the compressor but the compressor is NOT running when it should be, then the compressor probably has a short and needs replaced. Check the wiring the compressors wiring to be completely sure it is bad.

If the compressor is bad, it makes more sense sometimes to just buy a new refrigerator. Check around online and see what your best option may be.

If you know of an easier way to check to find out if a refrigerator compressor is bad, please leave a comment below. Tagged as: bad compressorbad motherboardfans worklights workrefrigeratorrefrigerator will not turn ontest compressortest motherboardvoltage to compressorwarm freezerwarm fridge. A year ago it stopped working and I unplugged it. I now have noted that when freezer not working but plugged in over 24 hours or longer the compressor is very very hot.

Refrigerator is Running but Not Cooling

Unplugging, the compressor cools down over several hours and then re plugging the freezer it starts working but only for 6 or even 24 hours then stops again I suppose when the compressor overheats.

I need to know how to wire a Westinghouse Refrigerator bjt-r. It is an Australian model that has the capacitor the overload relay and the start relay. I have trio GE refrigerator model Pfs22sisbss and the compressor is not kicking in i replaced the mother board on the back of the unit … and then i noticed i am not getting volts on the main harness of the mother board where you can bypass line and compressor.


thought on “Fridge compressor hot but not running”

Leave a Reply

Your email address will not be published. Required fields are marked *